Skip to content
Serving Chhattisgarh & Odisha Mon–Sat, 9:30 am – 6:30 pm
Instrumentation and flow control

Flow meters for water, slurry, air and steam in Odisha & Chhattisgarh

Flow meter selection based on what actually flows through your pipe: its conductivity, solids, temperature and pressure.

  • Electromagnetic
  • Clamp-on ultrasonic
  • Vortex for steam

Get a quick quote

Share your requirement — we call back with options and price.

We reply to most enquiries within one working day. Prefer to talk? Call +91 92010 87778. We only use your details to answer this enquiry.

No single flow meter suits every fluid. An electromagnetic meter that works perfectly on cooling water will not read oil, and a turbine meter that is accurate on clean diesel will wear quickly on slurry. Choosing by technology first, and size second, is how you get a reading you can trust.

We supply flow meters to steel, power, mining and process plants in Odisha and Chhattisgarh for water accounting, process control, effluent monitoring and utility metering. Share the fluid and line details, and we recommend the technology and size that fit.

In plants around Jharsuguda, Angul, Raigarh and Korba, flow meters are increasingly needed not only for process control but also for water accounting and reporting. Totalised readings for raw water, cooling make-up and effluent discharge help identify losses and support environmental compliance.

Where it is used

  • Cooling water and make-up water
  • Raw water intake and treatment
  • Effluent discharge monitoring
  • Steam distribution in power and process plants
  • Compressed air consumption audits
  • Fuel oil and diesel consumption
  • Slurry lines in mining and beneficiation
  • Dust suppression water supply
Instrumentation and flow control

Key benefits

Electromagnetic

No moving parts; ideal for water, effluent and slurry with some conductivity.

Clamp-on ultrasonic

Mounts outside the pipe; useful for audits and lines that cannot be cut.

Vortex for steam

Measures steam, gases and clean liquids with good turndown.

Sized to your line

Meter sized on actual flow range, not just pipe diameter.

Flow meter types and where they fit

TypeBest forAvoid when
ElectromagneticWater, effluent, slurry, acids (conductive liquids)Oils, hydrocarbons, DM water of very low conductivity
Ultrasonic (clamp-on or inline)Clean or slightly dirty water, large pipes, temporary auditsHeavily aerated liquids or poor pipe condition
VortexSaturated and superheated steam, compressed air, gases, clean liquidsVery low velocities or highly viscous fluids
TurbineClean, low-viscosity liquids such as diesel and clean waterLiquids with solids or fibres
Variable area (rotameter)Local indication of low flows of water, air or gasesRemote control loops needing high accuracy
Positive displacement / CoriolisFuel oil, viscous liquids, mass flow for custody or dosingLarge water lines where cost is high

Installation points that affect accuracy

  • Straight pipe runs: most meters need several pipe diameters of straight run upstream and downstream; bends, valves and pumps close by distort the flow profile.
  • Full pipe: electromagnetic and ultrasonic meters need the pipe running full; install in a rising section or low point where possible.
  • Velocity: a meter sized to the pipe but run at very low velocity loses accuracy; a reduced meter size can help.
  • Earthing: electromagnetic meters on plastic or lined pipes need earthing rings for a stable signal.
  • Steam: vortex meters on steam need pressure and temperature compensation for accurate mass flow.

What to send us for a quote

Fluid and its condition (clean, solids, chemicals), minimum, normal and maximum flow, pipe size and material, operating pressure and temperature, flange or thread standard, output needed (display, 4–20 mA, pulse, Modbus), power supply and quantity.

If you are unsure about pipe condition or flow range, a short site visit or a temporary clamp-on measurement can establish actual conditions before you invest in a permanent meter.

Need help choosing?

Send us your application, duty and site conditions. We recommend the right model and quote with delivery to your plant.

Related

FAQs

Flow Meter: questions buyers ask

Straight answers to the questions plant teams ask us most.

Which flow meter should we use for treated effluent discharge?

An electromagnetic flow meter is the usual choice, as effluent is conductive and may carry solids. It has no moving parts to clog, and can provide totalised flow for records and pollution control reporting.

Can we measure flow without cutting the pipe?

Yes, with a clamp-on ultrasonic flow meter. Its transducers mount on the outside of the pipe, which suits audits, temporary checks and lines that cannot be shut down. Pipe material, wall thickness and condition affect accuracy.

What flow meter works for steam?

Vortex flow meters are widely used for steam. For mass flow in kg/h, the meter or a flow computer should compensate for pressure and temperature.

Why does our electromagnetic meter read zero on DM water?

Electromagnetic meters need a minimum liquid conductivity. Demineralised water may fall below this threshold, so an ultrasonic or other technology is a better fit.

Should the meter be the same size as the pipe?

Not always. Size on the actual flow range so that velocity stays within the meter's accurate band. A smaller meter with reducers is often more accurate at low flows.

Can the flow meter send data to our PLC or SCADA?

Most meters offer 4–20 mA and pulse outputs, and many have Modbus or other communication options. Tell us the input on your control system.

Find the right flow meter

Send the fluid, flow range and pipe details, and we will recommend the meter type and size with a quotation.

Questions? Chat with us